Всем доброго дня! Есть не удаляемая ошибка
ECM-P061A62 Internal Control Module Torque Performance - Algorithm Based Failures - Signal compare failure
На приборке чека нет. Помогите интерпретировать ошибку. Возможно у кого то была такая.
Буду очень признателен.
D5 Ошибка по крутящему моменту ECM-P061A62
Re: D5 Ошибка по крутящему моменту ECM-P061A62
у вас одна ошибка или ещё появляются? может вы полный список до сброса покажете?!
Re: D5 Ошибка по крутящему моменту ECM-P061A62
Только эта ошибка активна. Остальные по фарам например удаляются после очистки.
- Attachments
-
Re: D5 Ошибка по крутящему моменту ECM-P061A62
Одновременно с такими вопросами, указывайте VIN автомобиля. Мне будет проще дать ответ
Re: D5 Ошибка по крутящему моменту ECM-P061A62
ECM-P061A62 Internal Control Module Torque Performance - Algorithm Based Failures - Signal compare failure
Information
The Engine Control Module (ECM) monitors the amount of torque produced by the engine. The torque is calculated using two different methods which do not share the same inputs (sensors). These values are compared to the expected engine torque, which is calculated using the vehicle speed and driver input information (e.g. the accelerator pedal).
Note! This fault has many possible causes. For example ECM software error, air intake system leaks, engine sensors fault, accelerator pedal fault.
Diesel specific information:
If the DTC still reoccurs after checking the possible causes, reset the TrqCalcNe adaptation values.
Drive the vehicle from high to low engine speed with fuel cut active to activate the adaptation process.
Test run criteria
The control module's test for the DTC starts when:
• The engine is running.
Detection criteria
The DTC is set if the control module detects that:
• The calculated engine torque is significantly higher than expected.
Fault handling in the control module
The Engine Control Module (ECM) temporarily limits the torque produced by the engine.
Information
The Engine Control Module (ECM) monitors the amount of torque produced by the engine. The torque is calculated using two different methods which do not share the same inputs (sensors). These values are compared to the expected engine torque, which is calculated using the vehicle speed and driver input information (e.g. the accelerator pedal).
Note! This fault has many possible causes. For example ECM software error, air intake system leaks, engine sensors fault, accelerator pedal fault.
Diesel specific information:
If the DTC still reoccurs after checking the possible causes, reset the TrqCalcNe adaptation values.
Drive the vehicle from high to low engine speed with fuel cut active to activate the adaptation process.
Test run criteria
The control module's test for the DTC starts when:
• The engine is running.
Detection criteria
The DTC is set if the control module detects that:
• The calculated engine torque is significantly higher than expected.
Fault handling in the control module
The Engine Control Module (ECM) temporarily limits the torque produced by the engine.
Re: D5 Ошибка по крутящему моменту ECM-P061A62
Подскажите как сбросить это значения адаптации TrqCalcNe?vtool wrote: ↑11 Mar 2025, 01:43 ECM-P061A62 Internal Control Module Torque Performance - Algorithm Based Failures - Signal compare failure
Information
The Engine Control Module (ECM) monitors the amount of torque produced by the engine. The torque is calculated using two different methods which do not share the same inputs (sensors). These values are compared to the expected engine torque, which is calculated using the vehicle speed and driver input information (e.g. the accelerator pedal).
Note! This fault has many possible causes. For example ECM software error, air intake system leaks, engine sensors fault, accelerator pedal fault.
Diesel specific information:
If the DTC still reoccurs after checking the possible causes, reset the TrqCalcNe adaptation values.
Drive the vehicle from high to low engine speed with fuel cut active to activate the adaptation process.
Test run criteria
The control module's test for the DTC starts when:
• The engine is running.
Detection criteria
The DTC is set if the control module detects that:
• The calculated engine torque is significantly higher than expected.
Fault handling in the control module
The Engine Control Module (ECM) temporarily limits the torque produced by the engine.
В VTool есть такая опция?